Skip to main content

How to make an obstacle avoiding robot

Post a Comment

How to make a vaccum cleaner with house hold item

In this article i am going to show you how to make a vacuum cleaner step by step with house hold materials.

A vacuum cleaner works by vacuum in which dust particles and dirt is sucked in with help of a fan which creates a partial pressure in the vacuum cleaner,here are the materials list you will need in making the cleaner.

Materials.

1.water bottle

2.glue gum

3.power jack

4.switch

5.can malt or soda can

6.knife blades

7.leather.

Now the steps:


1. Get a can malt or any can.

2.use a sharp paper to remove the bottom closure,u can even use a knife instead.

This how it looks like when you cut it out.

3.make a fold a tiny plastic into circuit,make sure it can fit into the can.4. Get a net like this.

4.gum it and trim it out like this

5.then place it to fit the can.

6.place it at the middle to form a compartment and gum it.

7.cut out a circle from another can malt.

8.divide it into sections

9.cut it out.

10.cut it to form a blade them apply gum.

11.gum the gear for connecting the blade to a motor.

12.make a base stand.

13.make a hole for the switch.

14.connect the switch to the DC motor.15.next make a DC power input connection as shown below.16.get a leather or plastic.

17.make holes for it .17.let cut the upper part of the can.

18.get an old plastic bottle and cut the upper top out.19.apply gum on the can and gum the bottle on it.

20.cut out the upper edge of the cover.

21.make a truncated mouth for it.

22.make an handle for your vaccum cleaner.

23.lastly power it with the input jack using a 9v or 12v DC power source.


Now testing time.

Thanks for reading and have a nice vaccum cleaner, don't forget to share this post to your friends and social media platforms.

Comments

Post a Comment

Popular posts from this blog

How to program an arduino with a smartphone.

H ow to program an arduino with a smartphone Before, we can only program an arduino with a laptop or desktop computer ,but most hobbyist doesn't can't afford to buy one but thanks to the new era of Technology we can now program our board with our smart phone any where we like and at any time.To program an arduino you need to download Arduino droid or arduino commander from the Google play store, I prefer arduino droid to Arduino commander because of it flexibility and ability to understand.To start coding with your phone you need a knowledge of c++ language,the Arduinodroid is both a compiler and an editor that is you can compile your skecth right after writing it. How to program with your smartphone . You will need an OTG cord to connect your Arduino to your phone for skecth uploading since the arduino cord can't directly connect to it.you can only use an android phone with version 2.0 or higher. When trying to upload your sketch the board will feed current from your phon...
Post a Comment
Read more

How to make a powerbank with 9v battery.

Home made 9v power bank. U  In this article we will learn how to make a power bank for our phones in case of emergency,smartphone has became a very unique device in the life of men but the only problem is the power source to keep it running on.we have many diy power banks we can make like rechargeables,4000mah power bank,non rechargeables,hand driven charger etc.So let's cut our story shot and go straight to the point. Materials. 1.ic7805cv that is for regulating 9v_5v 2.old USB. 3.wires for connection 4.LED,.1k resistor,if you wish to add an indicator bulb. 5.9v battery. Circuit diagram below. good luck!!!!
Post a Comment
Read more

Beginner guide to electrical components and description.

Electrical components are commonly found on circuit boards and their presence is ubiquitous in mordern engineering here are some lists of materials you need to be familiar at: 1.Capacitor Symbol of capacitors. It consists of two metals separated by a dielectric material,it is use for storing charges.types: Ceramic, electrolytic,film and vairable capacitors.electrolytic is grouped into aluminum and tantalumcapacitor.Applications range from storing electric charge, stabilizing current, reducing riples in voltage and use in radio for tuning. 2.Diode Diode symbol. It is use for rectifying DC from ac since it only allows current in one direction,the part with white strip is the negative pole known as the cathode while the other black area is the positive side called anode.types of diodes:Zener,LED known as light emmiting diode, photodiodes,avalanche diode. 3.Transistors Transistors. it is basically used for amplification,switching, regulating and control it is made of semiconductors and has...
Post a Comment
Read more